12/10/07 Model LE13A Text 1 Operator’s Manual Text Section I Model LE-13A Dake/Johnson Horizontal Band saw Fully Automatic DAKE Division of
12/10/07 Model LE13A Text 10CAUTION!!!!! THE GROUND WIRE MUST BE CONNECTED; FAILURE TO CONNECT THE GROUND WIRE CAN DAMAGE THE MACHINE AND VOID THE WA
12/10/07 Model LE13A Text 11 SECTION 4 4.1 Control Panel Description 1. POWER LIGHT This light will come on when the circu
12/10/07 Model LE13A Text 12 4. AUTO-MANUAL SELECTOR For Continuous cutting, turn this selector to To individually operate each function, turn thi
12/10/07 Model LE13A Text 1313. Vise shut off switch. When this switch is off the counter will not work. 14. FEEDING-TIMES PRESET COUNTER When a cut
12/10/07 Model LE13A Text 144.2 Blade change 1. Select the saw blade best suited for the work piece to be cut. Size and shape of the work piece and
12/10/07 Model LE13A Text 154. Properly position the blade guide according to the diameter (or the width) of the work piece to be cut. a. Pull the
12/10/07 Model LE13A Text 16u. After properly adjusting the position of the work piece, turn the vise clamp selector to “back vise open”, so that th
12/10/07 Model LE13A Text 174.5 Blade speed change 3. Adjust the saw blade speed. c. There is a handle just to the right of the motor, when loose
12/10/07 Model LE13A Text 18NOTE: 1. When setting the cutting length, be sure to turn the hand wheel clockwise past the desired length, then turn it
12/10/07 Model LE13A Text 19 6. Turn the auto-manual selector to AUTO and press the blade drive button. The blade will run and the automatic operat
12/10/07 Model LE13A Text 2 FOREWORD This manual has been prepared to acquaint you with the operation, maintenance, and serviceable components of yo
12/10/07 Model LE13A Text 204. Set the switch to bundle cutting (item 13 pages 11). 5. Position the work piece for bundle cutting. Allowable clam
12/10/07 Model LE13A Text 212. The break-in operation can be considered sufficient if all unusual noises or metallic sounds have been eliminated. (F
12/10/07 Model LE13A Text 22 6.2 Lubrication Description Lubricant Hydraulic Oil DTE 24 Hydraulic oil Gearbox Oil 80/90 Synthetic gear lube Dr
12/10/07 Model LE13A Text 23 SECTION 8 – TROUBLE SHOOTING CHART 8.1 Machine has power but will not start cut in Semi-Auto mode Vibration during cu
12/10/07 Model LE13A Text 24 8.1 Minor trouble shooting Symptom Probable Cause Corrective Action Hydraulic pump motor does not run even though hy
12/10/07 Model LE13A Text 3 CONTENTS SECTION 1 – Safety 1.1 General Product specifications 1.2 General Safety Instructions 1.3 Location of Safety La
12/10/07 Model LE13A Text 4 1.1 General Product Specifications Machine Type Horizontal scissors type Rapid Head Approach Sure stop hydraulically con
12/10/07 Model LE13A Text 5 SECTION 1 1.2 General Safety Instruction Read and understand the instruction manual and warning signs before operating t
12/10/07 Model LE13A Text 6 Location of Safety Labels 1.3 SAFETY
12/10/07 Model LE13A Text 7 2.1 Machine Life The intended life limit of this machine is ten years under normal operating conditions and with good
12/10/07 Model LE13A Text 8 LE13A Item Metric English Machine Weight W 1492 Kg 3,290 lbs Capacity, T 2 ton 2 ton Length of the Fork, L1 1.5 m
12/10/07 Model LE13A Text 9 Figure 3.4 Warning!!!! Failure to remove this bracket could cause damage to the machine and void the warranty.
Kommentare zu diesen Handbüchern